LOADING...

Sunday, May 28, 2017

Drawstring Bunny Bag Tutorial

How to Sew simple Drawstring Bunny Bag. Tutorial & Pattern
Materials to make a Drawstring Bunny Bag

   - Fabric for bag and outer ears (a woven cotton works best)
   - Contrasting fabric for inner ears (a woven cotton works best)
   - 1/4 inch ribbon or rope for drawstring
   - common sewing supplies
 Bunny Bag Template
Now, cut 4 of the “Main Bag” pieces and 2 of the “Bunny Ear” pieces, in the same color fabric. Then cut 2 rectangle pieces out of the same fabric (for your ribbon guides) that are 6.5 x 1.5 inches. Lastly, cut 2 of the “Bunny Ear” pieces out of a contrasting color.
Place one of the main ear pieces together with one of the contrasting ear pieces and match them up with RIGHT sides together. Using a 1/4 inch seam allowance, sew up one side and down the other.
Trim a little excess fabric off the curve and tip, to reduce some of the bulk.
Turn right side out and iron flat. Repeat with the other 2 ears pieces.
Place one of your “Main Bag” pieces in front of you with the RIGHT side facing up. Place the 2 finished ears on top, with the contrasting fabric facing down. Place the 2 ears 3/8 inch apart, lining up the raw edges of the ears with the upper straight edge of the “Main Bag” piece. Using a basting stitch, attach the ears using a 1/4 inch seam allowance.
Place one of the other “Main Bag” pieces right on top, with the RIGHT side of the fabric facing down…and match up all the edges.
Sew along the upper edge, using a 1/2 inch seam allowance. Place the other 2 “Main Bag” pieces together the same way (without the ears) and sew along the top straight edge as well.
Flip these piece right side out and iron flat.
Lay your 2 rectangle ribbon guide pieces down in front of you with the RIGHT side of the fabric facing down. Fold each long edge in towards the center and iron flat.
Fold over each end 3/8 inch towards the WRONG side, then another 3/8 inch, press flat with your fingers, and then sew in place.
Now, place the 2 bag pieces in front of you again and turn the piece with the ears attached over so that the contrasting color is facing down. Place the 2 ribbon guides on top of the bag pieces (this will be the OUTSIDE of the bag), centering them right to left. Adjust each ribbon guide so that they’re 1 inch from the upper edge. Sew along the upper and lower edges of each ribbon guide, leaving each end open for the ribbon to slide through.
The next few steps are optional but if you really want to make your bag darling, add a simple little face to it! The easiest way is to use a pencil to draw on the face exactly how you want it. (Be mindful to not draw it too low, because there will be a seam allowance subtracted down below.)
You can add your face with whatever stitches suit you best but I just used a quick whip stitch for the main portion of the nose and then to create the lines for the mouth.
Now, place the two bag pieces together with RIGHT sides together and stitch along the sides and bottom, using a 1/4 inch seam allowance. Then, add a zig-zag stitch to add some extra reinforcement.
Trim away the excess fabric if needed.
Turn the bag right side out and iron flat.
Use a safety pin to help you thread a 20-inch long piece of ribbon through the front ribbon guide from right to left and then continue through the back ribbon guide from left to right.
Grab a second 20-inch long piece of ribbon and thread through the front ribbon guide from left to right and then continue through the back guide from right to left.
Pull each ribbon so that it’s pulled evenly. Then tie a knot into the ribbon ends on each side. Cut off excess ribbon.
Now, if you pull the ribbons at each side, the bag will cinch right in!
How to Sew simple Drawstring Bunny Bag. Tutorial & Pattern
And that’s it! Now fill with candy, toys, coins, or whatever…..and enjoy your cute little Bunny Bags!
How to Sew simple Drawstring Bunny Bag. Tutorial & Pattern

How to Sew simple Drawstring Bunny Bag. Tutorial & Pattern
Author:

0 comments:

Post a Comment